[NTLK] :Re: Plan for Performing eMate 300 Hinge Repair
sheflinm at gmail.com
Sat Apr 17 10:16:25 PDT 2021
Spare CD/hard drives (etc.) work decently for practice. You definitely
don't want to try to reflow solder for the first time on something you
don't want to potentially be (catastrophically) destroyed. Soldering is
not hard, but it requires some familiarity with techniques and temperatures.
My first experiment likely destroyed the internal traces on an SE/30
motherboard. Luckily, the board was almost certainly dead to begin with,
but it was an instrumental lesson.
On Sat, Apr 17, 2021, 10:06 AM Alan Grassia <alan.grassia at gmail.com> wrote:
> Hello Allen and Newton Friends,
> Thank you for sharing those two links, Allen. I watched the video and
> read the soldering guide. I thought that both were well done. I
> appreciated the video as it does give me an idea of how to rejoin the wires
> to the solder joint.
> Unfortunately, I don't have any other electronics or spare parts to
> experiment with. The eMate that I have is it. I have been in the IT field
> for a long time so I don't mind taking apart the eMate and working inside
> it. Since I only need to disconnect and reconnect the four wires, I feel
> like I will be up to the task.
> Thanks again for the links. I feel that they have made me better prepared
> for the repair job on my (new to me) eMate.
> I will likely do the work next weekend. I will be sure to let everyone
> know how I make out.
> Alan Grassia
> MessagePad 2000, MessagePad 2100, eMate 300
> Website: http://blog.smartphonefanatics.com
> Twitter: https://twitter.com/alanmgrassia
> LinkedIn: https://www.linkedin.com/in/alangrassia
> On 4/16/21, 3:32 PM, "NewtonTalk on behalf of Allen Russell" <
> newtontalk-bounces at newtontalk.net on behalf of Allen.Russell at messer-us.com>
> I would just add: if you read Frank's site you know the repair is
> Forrest's instructions are good, but soldering does take practice. I
> recommend youtube to see how it's done. It's easy to use too much solder
> and make a mess, usually because the solder is hot, but the wires are not
> hot enough for the solder to flow. Practice on something that's not an
> Example: https://www.youtube.com/watch?v=QKbJxytERvg
> And this is a good write-up:
> >Date: Thu, 15 Apr 2021 23:22:29 -0700
> >From: Forrest <newton_phoenix at mindspring.com>
> >To: newtontalk at newtontalk.net
> >Subject: Re: [NTLK] Plan for Performing eMate 300 Hinge Repair
> >Message-ID: <1F53095E-3681-45C4-99F9-2FE85353082D at mindspring.com>
> >Hi Alan:
> >Yes that one will do nicely.
> >Hotter is not necessarily better. I have a soldering gun that if I
> recall is something like 100 watts or more. That will obliterate most
> simple soldering jobs.
> >You will find the soldering work to be remarkably easy, and I?m not
> just saying that because I have experience. Follow the instructions?plug in
> the iron and allow it to >become hot. It?s a good idea to ?tin? the tip of
> the iron the first time you use it. This ?tinning? is nothing more than
> applying solder to the tip and allowing it to melt?of >course, once it
> becomes hot?then wiping off the excess with a rag. I like to tin the tip a
> couple of times. A properly tinned tip will conduct heat better and will
> therefore be >more useful.
> >Desoldering the wires is as simple as touching the hot tip to the
> wire. In most cases the wire will come loose on its own, but if not grasp
> it and gently pull it free. Re->soldering is much the same, except you are
> now holding the wire to the terminal you want to connect with, and touching
> the hot iron to that joint. In most cases you will >not need any additional
> solder to make that union.
> >Congratulations, you have completed your first soldering task!
> >> On Apr 15, 2021, at 6:45 PM, Alan Grassia <alan.grassia at gmail.com>
> >> Two weeks ago I purchased an eMate 300 in good condition on eBay.
> I received it about a week ago. Having read the recent posts here, I get,
> I need to open this eMate up and check for and possibly do the hinge repair.
> >> Reading the eMate 300 disassembly directions on Frank?s website,
> Pda-Soft.de at
> >> I do not have any skills with electrical wiring or soldering. Is
> it possible for me to disassemble the eMate without desoldering the four
> wires on the system board?
> >> If the answer is ?No?, or ?It?s really more difficult that way?, is
> there a specific soldering iron that I should look for to heat up the
> solder to remove/reinstall the four wires?
> >> For example, is there a difference in soldering iron kits? Is a
> >> 25-Watt soldering iron better than a 40-Watt soldering iron for this
> >> kind of work? Here?s an example of a soldering iron kit that a
> >> home improvement store has for sale:
> >> What do you folks think? I accept that I need to do the repair.
> I?m looking for some guidance about how best proceed.
> >> Thanks in advance.
> >> Cheers,
> >> Alan Grassia
> The information contained in this email and any attachments may be
> confidential and is provided solely for the use of the intended
> recipient(s). If you are not the intended recipient, you are hereby
> notified that any disclosure, distribution, or use of this e-mail, its
> attachments or any information contained therein is unauthorized and
> prohibited. If you have received this in error, please contact the sender
> immediately and delete this e-mail and any attachments. No responsibility
> is accepted for any virus or defect that might arise from opening this
> e-mail or attachments, whether or not it has been checked by anti-virus
More information about the NewtonTalk